Leather is a natural material and needs oil/moisture to keep it soft and supple. To stop it drying out, hardening and cracking, treat it at least once a month with Renapur Leather Balsalm. Use a sponge or cloth and work the cream into both the toe creases and around the sole unit of your Boudicas.

Please note: exposure to salt water or animal waste / ammonia may cause degradation of the leather and the lining, and prevent it from performing effectively.

Not in the washing machine, please!
Clean the leather with a neutral-coloured microfibre cloth and leave it to dry naturally. Remove mud and dirt immediately to stop moisture being drawn from the leather.Always read the directions of the care product, and test on an inconspicuous area first. Fairfax & Favor cannot be held responsible for improper use of care or cleaning products. For any concerns, please contact our Customer Service team.

Store your beautiful Boudicas away from heat, damp and direct sunlight. Where possible, store your boots in their dustbags and blue box.

Once you’ve used your Fairfax & Favor Boudicas a bit, you can treat them with either Suede & Nubuck Protector once a month or Liquiproof Premium Protector every couple of months – more often if you’re using a lot.

Spray the Suede & Nubuck Protector lightly and sparingly from at least a foot away and leave to prove for an hour.

If you’re using Liquiproof Premium Protector, apply sparingly section by section, brushing it in with a soft brush until the nubuck has been covered.

Please note: exposure to salt water or animal waste / ammonia may cause degradation of the leather and the lining, and prevent it from performing effectively.

Not in the washing machine, please!
Remove dried dirt or marked fibres using a soft suede brush. If it’s still dirty, use Liquiproof Eco Cleaner on light marks but dilute it heavily in warm water. If they become wet, leave them to dry naturally and brush. If anything else gets onto your product (like a wine glass accident), soak it up immediately and then wipe over with a lightly damp, neutral-coloured microfibre cloth.

Always read the directions of the care product, and test on an inconspicuous area first. Fairfax & Favor cannot be held responsible for improper use of care or cleaning products. For any concerns, please contact our Customer Service team.

Store away from heat, damp, and direct sunlight. Where possible, store in their dustbags and the blue box provided for additional protection.

Please Note: Bright coloured nubuck can transfer with wear onto other fabrics and leave a mark. Likewise, dark coloured fabrics (like denim!) can also transfer onto brighter coloured suede and/ or leathers. This is perfectly normal and won't be covered under our warranty.

Once you've used them a bit, you can treat your Boudicas with either Suede & Nubuck Protector once a month or Liquiproof Premium Protector every couple of months – more often if you're wearing them a lot.
Spray the Suede & Nubuck Protector lightly and sparingly from at least a foot away and leave to prove for an hour. If you’re using Liquiproof Premium Protector, apply sparingly section by section, brushing it in with a soft brush until the suede has been covered.

Please note: exposure to salt water or animal waste / ammonia may cause degradation of the leather and the lining, and prevent it from performing effectively.

Not in the washing machine, please!
Remove dried dirt or marked fibres using a soft suede brush, brushing in the direction of the suede. If it’s still dirty, use Liquiproof Eco Cleaner on light marks but dilute it heavily in warm water. If your boots get wet, leave them to dry naturally and brush. If anything else gets onto your Boudicas (like a wine glass accident), soak it up immediately and then wipe over with a lightly damp, neutral-coloured microfibre cloth.

Always read the directions of the care product, and test on an inconspicuous area first. Fairfax & Favor cannot be held responsible for improper use of care or cleaning products. For any concerns, please contact our Customer Service team.

Store away from heat, damp, and direct sunlight. Where possible, store in their dustbags and the blue box provided for additional protection.

Please Note: Bright coloured suede & leather can transfer with wear onto other fabrics and leave a mark. Likewise, dark coloured fabrics (like denim!) can also transfer onto brighter coloured suede and/ or leathers. This is perfectly normal and won't be covered under our warranty.

Leather is a natural material and needs oil/moisture to keep it soft and supple. To stop it drying out, hardening and cracking, treat it at least once a month with Renapur Leather Balsalm. Use a sponge or brush and work the cream into both the toe creases and around the sole unit of your boots. A small time maintaining the outer leather will help your boots perform for many years.

Dry, cracked, or dirty leather can prevent the waterproof Sympatex ® membrane from performing effectively.

Please note we recommend tightening the screw backs on the tassels once you receive your new boots, this will help ensure no lost tassels!

If you happen to lose the screw back off of your Fairfax & Favor tassel, we have Replacement screw backs available, Alternatively, if you have lost a tassel, please contact our Customer Service team who will be able to assist you further.

Not in the washing machine, please!
Clean the leather with a neutral-coloured microfibre cloth and leave it to dry naturally. Remove mud and dirt immediately to stop moisture being drawn from the leather.

Always read the directions of the care product, and test on an inconspicuous area first. Fairfax & Favor cannot be held responsible for improper use of care or cleaning products. For any concerns, please contact our Customer Service team.

The Explorers are tested to British Industry standards for 8 hours to confirm no water ingress. This means that the boots are waterproof to the elements for up to 8 hours if they are maintained properly*.
However, like all leather performance boots, excessive exposure will cause water absorption into, and eventually through, the leather. After exposure to water, the boots must be dried out fully at natural room temperature, and not in direct heat or sunlight. If the boots are not fully dried out after use, the length of time that the boots will remain fully waterproof may be lessened. Similarly, exposure to salt water or animal waste / ammonia may cause degradation of the leather and the lining, and prevent it from performing effectively.

The Vibram® soles, are heavy duty and are tested to British Industry Standards for slip resistance, flex, and wear.
To care for your soles, remove stones and clean thoroughly after use.

Punctures to the sole, insole damage and nicks/tears in the lining can all affect the waterproof ability of the boot.

Store away from heat, damp, and direct sunlight. Where possible, store in their dustbags and the blue box provided for additional protection.

We recommend using Boot Trees to fill out the calf, maintain their original shape and prevent ankle creasing. Where possible use a Signature Boot Bag for extra protection when travelling.

*Whilst the boots are tested to be waterproof in everyday conditions, puddles and wet grass etc. We do not recommend fully submerging or wading in them. For this type of activity the only true protection would be a rubber wellington.

To ensure your L'Alliance rubber boots stay in good condition it's important that they are regularly cleaned with water and allowed to dry naturally.

Occasionally you might notice a white powdery "Bloom" on the boots. This is perfectly normal and is insoluble particles that have risen to the surface, which is largely due to the characteristic of a premium product made from high-grade rubber and will not compromise the durability or performance of the boots.

Keep the zip clean and never force the zip. Dirt will wear the zip and significantly reduce its life, and don't leave the zip undone when wearing the boots, this will increase the chances of dirt getting into the zip.

Please note we recommend tightening the screw backs on the tassels once you receive them, this will help ensure no lost tassels!

If you happen to lose the screw back off of your Fairfax & Favor tassel, we have Replacement screw backs available, Alternatively, if you have lost a tassel, please contact our Customer Service team who will be able to assist you further.

Not in the washing machine, please!
Remove dried dirt using water and a soft brush. Let the boots air dry.

Store away from heat, damp, and direct sunlight. Where possible, store in their dustbags and the blue box provided for additional protection.

We recommend using Boot Trees to fill out the calf, maintain their original shape and prevent ankle creasing. Where possible, store your boots in the box they arrived in, and use a Le Chameau boot bag for extra protection when travelling.

Leather is a natural material and needs oil/moisture to keep it soft and supple. To stop it drying out, hardening and cracking, treat it at least once a month with Renapur Leather Balsalm.

Dry, cracked, or dirty leather can prevent the waterproof Sympatex ® membrane from performing effectively. Use a sponge or brush and work the cream into both the toe creases and around the sole unit of your Malvern's.

A small time maintaining the outer leather will help your boots perform for many years.

Not in the washing machine, please!
Clean the leather with a neutral-coloured microfibre cloth and leave it to dry naturally. Remove mud and dirt immediately to stop moisture being drawn from the leather. Then re-apply the Renapur Leather Balsalm afterwards to reintroduce the required oils and moisture content.

Always read the directions of the care product, and test on an inconspicuous area first. Fairfax & Favor cannot be held responsible for improper use of care or cleaning products. For any concerns, please contact our Customer Service team.

The Malvern's are tested to British Industry standards for 8 hours to confirm no water ingress. This means that the boots are waterproof to the elements for up to 8 hours if they are maintained properly*.

However, like all leather performance boots, excessive exposure will cause water absorption into, and eventually through, the leather. After exposure to water, the boots must be dried out fully at natural room temperature, and not in direct heat or sunlight. If the boots are not fully dried out after use, the length of time that the boots will remain fully waterproof may be lessened. Similarly, exposure to salt water or animal waste / ammonia may cause degradation of the leather and the lining, and prevent it from performing effectively.

Punctures to the sole, insole damage and nicks/tears in the lining can all affect the waterproof ability of the boot.

Store your new boots away from heat, damp and direct sunlight. Where possible, store your boots in their dustbags and blue box, and use a Signature Boot Bag for extra protection when travelling.

*Whilst the boots are tested to be waterproof in everyday conditions, puddles and wet grass etc. We do not recommend fully submerging or wading in them. For this type of activity the only true protection would be a rubber wellington. Please note that excess moisture that is retained in your footwear can accelerate the insoles coming loose in your shoe.

This product contains recycled materials. 100% Polymide Shell, 100% Recycled polyester Lining

Pertex® Quantum fabric unique fabric has enabled Musto to engineer products that ensure maximum comfort during intense activities. It's waterproof construction can withstand heavy downpours, whilst the fabric's weave provides high levels of breathability, ensuring you're dry and comfortable on any adventure. Equipped with PrimaLoft® Thermoplume Cross Core insulation technology, originally designed for the US military, this stylish product will keep you warm but also dry thanks to the Pertex waterproof outer fabric.
For more information on how to care for your Pertex® Quantum fabric please follow the link for Musto product care guide.

To ensure longevity and top performance, make sure you only wash your garments when they really need it. Wash your Musto garments using a non-biological product on a gentle cycle at 30°C or less. Our favourite is Granger’s Performance Wash . Do not use, under any circumstances, biological detergents.

Close hook and loop before washing, Close zippers before washing, Do not iron, Do not use fabric softener, Use liquid detergent, Do not use biological washing detergent, Wash with similar colours. Dry inside out on a line, Remove promptly from the dryer, Remove promptly from the Washer, Wash inside out. Wash Seperatley.
lightly tap channels during and after drying to spread the insulation evenely.

We recommend that you read the care labels inside your garments carefully as this will provide specific information for your product.

Store your garment once you are sure it is perfectly dry. It might be worth letting it dry naturally for an extra day to ensure all moisture has left the garment, especially when storing your product at the end of the sailing season.

Store away from heat, damp, and direct sunlight. Lay flat if possible; otherwise, use a broad hanger instead of the decorative loop to help prevent wrinkles.

This product contains recycled materials. 100% Polyester Shell, 100% Recycled polyester Lining

A high tech lifestyle piece that will keep you warm and dry in style. Part of the Fairfax and Favor luxury edit, this product benefits from a BR2 10k waterproof rating. A layer of top quality PrimaLoft® BLACK Eco insulation protects against bitterly cold temperatures when your feet are firmly on land.

Musto treats the waterproof garments BR2 products, with a durable water repellent (DWR) treatment. This polymer prevents the garment outer fabric from being saturated with water. Wear and tear, salt, dirt or repeated washing can wear off the DWR treatment. Your garment may even appear to be leaking because the waterlogged outer is reducing the jacket’s breathability, creating condensation on the inside. When this happens, or to prevent this from happening, you will need to re-treat your product. We recommend you treat your garment only when the DWR performance begins to lower - it does not have to be after every single wash. You can test the DWR performance by sprinkling water on the fabric. If the water beads up and rolls off, the DWR does not need renewing. Reproofing will avoid you getting an uncomfortable wet out feeling that can rapidly put an end to your day out.

Musto recommends Granger’s Performance Repel or Clothing Wash and Repel to renew the DWR. Please follow the instructions on the re-proofing product.
For more information on how to care for your Pertex® Quantum fabric please follow the link for Musto product care guide.

To ensure longevity and top performance, make sure you only wash your garments when they really need it. Wash your Musto garments using a non-biological product on a gentle cycle at 30°C or less. Our favourite is Granger’s Performance Wash . Do not use, under any circumstances, biological detergents.

Close hook and loop before washing, Close zippers before washing, Do not iron, Do not use fabric softener, Use liquid detergent, Do not use biological washing detergent, Wash with similar colours. Dry inside out on a line, Remove promptly from the dryer, Remove promptly from the Washer, Wash inside out. Wash Seperatley.
We recommend that you read the care labels inside your garments carefully as this will provide specific information for your product.

Store your garment once you are sure it is perfectly dry. It might be worth letting it dry naturally for an extra day to ensure all moisture has left the garment, especially when storing your product at the end of the sailing season.

Store away from heat, damp, and direct sunlight. Lay flat if possible; otherwise, use a broad hanger instead of the decorative loop to help prevent wrinkles.

Halley Stevensons Dry Wax cotton, cracks, creases and patinas, which is part of its beautiful character. This finish is a combination of their driest wax and soft aero tumbling. This emulsified wax finish is perfect for lightweight breathable and weather repellent garments.

Naturally through wear, the wax will gradually come off the fabric. Depending on the usage you will start to notice some fading in areas revealing the original dyed shade of fabric (applying wax darkens the dyed shade). This is due to the wax rubbing against itself and from movement (i.e. at the elbows).

You can treat your waxed cotton product with Halley Stevensons Reproofing Spray once wear starts to show. Always read the directions of the care product, and test on an inconspicuous area first. Fairfax & Favor cannot be held responsible for improper use of care or cleaning products. For any concerns, please contact our Customer Service team.

Not in the washing machine, please!
Remove dried dirt or marked fibres with clean warm water and a neutral-coloured microfibre cloth - leave it to dry naturally. Avoid aggressive detergents or rubbing with abrasive materials.

For toucher stains please Dry Clean & then Reproof with Halley Stevensons Reproofing Spray. Do not rub, do not soak, do not iron, and do not wring out. Dry Flat, and don't store damp.

Keep out of reach of children. Avoid contact with eyes and prolonged contact with skin. Use in a well-ventilated area.

Store away from heat, damp, and direct sunlight. Lay clothing flat if possible; otherwise, use a broad hanger instead of the decorative loop to help prevent wrinkles.

The water-resistant treatment that is applied at production is not impermeable and may wear away with washing of the product.